QuickLabel Systems QLS-4100X Setup Guide Page 23
- Page / 118
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
QLS-4100 X 23
Compressed Air Connection
Preparing the Air Regulator
When you receive the QLS-4100 X Printer, the Air Intake Regulator is ready for
operation. The air pressure regulator has been set at the factory for the proper air
pressure. You only need to connect your in-house air supply to the printer.
QuickLabel Systems can supply you with a portable, quiet air compressor suitable
for office use should you not have a source of compressed air.
Connecting the Air Supply
Obtain a suitable source of in-house air. Be sure to turn off the supply of air to this
connection before making any connections.
Attach an appropriate threaded fitting to the Air Intake Regulator using Teflon tape
on the threads to seal the fitting.
Attach your in-house air source to the Air Intake Regulator.
Turn on the supply of air to this connection.
Check the indicator dial to ensure that the regulator is set to 70 PSI.
If adjustment is required, pull down on the regulator knob to unlock it and turn the
knob until the desired pressure level is reached:
• Turn the knob clockwise to increase air pressure
• Turn the knob counterclockwise to decrease air pressure
When finished adjusting the pressure, push the regulator knob upwards to lock it
into place.
Note
The QLS-4100 X can be used without compressed air, but the
RibbonRation system cannot be used. Refer to Chapter 5 for information
on how to disable the RibbonRation system.
1
2
3
4
5
6
7
- Operation & Setup Guide 1
- Table of Contents 3
- 1 Quick Start 7
- QuickLabel Systems Media 8
- Quick Start Guide 9
- 2 Physical Setup 10
- Unpacking the Printer 11
- Printer Orientation 12
- Features of the QLS-4100 X 13
- Side View 14
- Rear Panel View 15
- Installing the Unwind Mandrel 16
- Power Connection 17
- Computer Connections 18
- Centronics Parallel Port 19
- RS-232 Serial Port 20
- Network Connection 21
- Utility Port Connection 22
- Compressed Air Connection 23
- DIP Switch Settings 24
- 3 Loading Media and 26
- Calibration 26
- Loading Label or Tag Media 29
- Adjusting the Media Sensor 32
- Calibrating Media 33
- Pause: Gap 35
- Calibration Bad 35
- 4 Keypad Controls 39
- and Menus 39
- Keypad Layout and Functions 40
- Deletes all labels 41
- SELECT to confirm 41
- Menu Functions 42
- Print Speed 43
- Pause: Speed 43
- Speed = 4 in/s * 43
- Print Intensity 44
- Pause: Intensity 45
- Head 1 = 12 * 45
- Print Offset 46
- Pause: Print Offset 46
- Offset = 0 * 46
- Windows Print Mode 48
- Ready: Windows Print 48
- Repeat 10 Label(s) 48
- Mirror Mode 49
- Pause: Mirror Mode 49
- Cutter Flag 50
- Pause: Cutter 50
- Flag Off * 50
- Cutter Offset 51
- Offset = 0 * 51
- Print Line Adjustment 52
- Pause: Test Print 52
- Proc. Block Pattern (CMYK) * 52
- Pause: Print Line Adj 53
- Head 1 = -4 * 53
- Cross Web Adjustment 54
- Pause: Cross Web Adj 55
- Head 1 = < 5 * 55
- TTR Sensor 56
- Pause: TTR Sensor 56
- Enabled * 56
- Calibrate 57
- Test Print 58
- Test Pattern: 1 in * 58
- Factory Reset 59
- Pause: Factory Reset 59
- Press SELECT 59
- Resets all settings 59
- QLS Settings 61
- Pause: QLS Settings 61
- SELECT to print 61
- System Baseline 62
- Pause: Sys Baseline 62
- Baseline = +3 * 62
- TTR / Media 63
- Pause: TTR/Media 63
- Standard * 63
- TTR Drop 64
- Pause: TTR Drop 64
- Head 1 = 22 * 64
- 5 Operation 65
- Printing with the QLS-4100 X 66
- RUN with NO AIR ? 67
- Press: Select 67
- Printer Indicators 68
- Error Messages 69
- Format Error 70
- Head x up 70
- SELECT to disable 70
- Head x Disabled 70
- Drive Roll Up 70
- Printheads Disabled 71
- Hd1 Hd2 Hd3 Hd4 71
- Color Alignment 72
- Evaluating print quality 77
- Advancing the Media 78
- Adjusting the Print Speed 79
- Printing Labels 81
- Printing Test Patterns 82
- 6 Advanced 83
- Adjustments 83
- Printhead Tangency Alignment 84
- Tools Needed 85
- Printhead Lift 87
- Adjusting System Baseline 88
- 7 Maintenance 89
- and Repair 89
- Recommended Tool List 90
- Routine Cleaning 91
- Printhead Replacement 92
- Platen Replacement 94
- Drive Roll Replacement 95
- Pinch Roller Replacement 96
- Firmware Upgrades 98
- Appendix A 99
- Physical Data 99
- QLS-4100 X Dimensions 100
- Appendix B 102
- Specifications 102
- QLS-4100 X Specifications 103
- Appendix C 104
- Replacement Parts 104
- Color QuickLabel 99 Pro 106
- Appendix D 106
- Color QuickLabel 99 Pro Setup 107
- Appendix E 111
- Windows Printer Driver 111
- Windows Printer Driver Setup 112
© 2020, manymanuals.com. All rights reserved. | 1.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals