QuickLabel Systems QLS-4100X Setup Guide Page 77
- Page / 118
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
QLS-4100 X 77
Evaluating print quality
Press the PRINT / PAUSE key to put the printer into the pause mode.
Press the NEXT or PREVIOUS key until the Test Print menu is displayed.
Press the + or - key to scroll through the test patterns and select Test Pattern: x in.
at a width that is appropriate for the width of your media. Print widths for the Test
Pattern are 1, 2, 3, 4, or 5 inches.
Press the SELECT key again to start the printing of the line test pattern.
Evaluate the test pattern to determine if printing is uniformly solid and crisp.
Press the PRINT / PAUSE key at any time to stop printing.
If print quality is not satisfactory, allow the test pattern to continue to print and
press the NEXT or PREVIOUS key to access any of the four parameters that can
be adjusted while operating in the test print mode. The parameters that can be
changed are: print speed, print intensity for each printhead, print line
adjustment for heads 1, 2, and 3, and cross web adjustment for each printhead.
As each parameter is displayed, press the + or - key to adjust the selected setting.
As you change the parameter settings, examine the test pattern to ensure that the
changes you are making are improving print quality.
Continue to adjust the parameter settings until you are satisfied that print quality
has been optimized.
1
2
3
4
5
6
7
8
9
- Operation & Setup Guide 1
- Table of Contents 3
- 1 Quick Start 7
- QuickLabel Systems Media 8
- Quick Start Guide 9
- 2 Physical Setup 10
- Unpacking the Printer 11
- Printer Orientation 12
- Features of the QLS-4100 X 13
- Side View 14
- Rear Panel View 15
- Installing the Unwind Mandrel 16
- Power Connection 17
- Computer Connections 18
- Centronics Parallel Port 19
- RS-232 Serial Port 20
- Network Connection 21
- Utility Port Connection 22
- Compressed Air Connection 23
- DIP Switch Settings 24
- 3 Loading Media and 26
- Calibration 26
- Loading Label or Tag Media 29
- Adjusting the Media Sensor 32
- Calibrating Media 33
- Pause: Gap 35
- Calibration Bad 35
- 4 Keypad Controls 39
- and Menus 39
- Keypad Layout and Functions 40
- Deletes all labels 41
- SELECT to confirm 41
- Menu Functions 42
- Print Speed 43
- Pause: Speed 43
- Speed = 4 in/s * 43
- Print Intensity 44
- Pause: Intensity 45
- Head 1 = 12 * 45
- Print Offset 46
- Pause: Print Offset 46
- Offset = 0 * 46
- Windows Print Mode 48
- Ready: Windows Print 48
- Repeat 10 Label(s) 48
- Mirror Mode 49
- Pause: Mirror Mode 49
- Cutter Flag 50
- Pause: Cutter 50
- Flag Off * 50
- Cutter Offset 51
- Offset = 0 * 51
- Print Line Adjustment 52
- Pause: Test Print 52
- Proc. Block Pattern (CMYK) * 52
- Pause: Print Line Adj 53
- Head 1 = -4 * 53
- Cross Web Adjustment 54
- Pause: Cross Web Adj 55
- Head 1 = < 5 * 55
- TTR Sensor 56
- Pause: TTR Sensor 56
- Enabled * 56
- Calibrate 57
- Test Print 58
- Test Pattern: 1 in * 58
- Factory Reset 59
- Pause: Factory Reset 59
- Press SELECT 59
- Resets all settings 59
- QLS Settings 61
- Pause: QLS Settings 61
- SELECT to print 61
- System Baseline 62
- Pause: Sys Baseline 62
- Baseline = +3 * 62
- TTR / Media 63
- Pause: TTR/Media 63
- Standard * 63
- TTR Drop 64
- Pause: TTR Drop 64
- Head 1 = 22 * 64
- 5 Operation 65
- Printing with the QLS-4100 X 66
- RUN with NO AIR ? 67
- Press: Select 67
- Printer Indicators 68
- Error Messages 69
- Format Error 70
- Head x up 70
- SELECT to disable 70
- Head x Disabled 70
- Drive Roll Up 70
- Printheads Disabled 71
- Hd1 Hd2 Hd3 Hd4 71
- Color Alignment 72
- Evaluating print quality 77
- Advancing the Media 78
- Adjusting the Print Speed 79
- Printing Labels 81
- Printing Test Patterns 82
- 6 Advanced 83
- Adjustments 83
- Printhead Tangency Alignment 84
- Tools Needed 85
- Printhead Lift 87
- Adjusting System Baseline 88
- 7 Maintenance 89
- and Repair 89
- Recommended Tool List 90
- Routine Cleaning 91
- Printhead Replacement 92
- Platen Replacement 94
- Drive Roll Replacement 95
- Pinch Roller Replacement 96
- Firmware Upgrades 98
- Appendix A 99
- Physical Data 99
- QLS-4100 X Dimensions 100
- Appendix B 102
- Specifications 102
- QLS-4100 X Specifications 103
- Appendix C 104
- Replacement Parts 104
- Color QuickLabel 99 Pro 106
- Appendix D 106
- Color QuickLabel 99 Pro Setup 107
- Appendix E 111
- Windows Printer Driver 111
- Windows Printer Driver Setup 112
© 2020, manymanuals.com. All rights reserved. | 0.274 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals