QuickLabel Systems QLS-4100X Setup Guide Page 46
- Page / 118
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
QLS-4100 X 46
By default, when printing on media with registration marks (gaps, reflective marks,
etc.), the printer will place the label image area between the registration marks.
You can, however, use the print offset adjustment to adjust print registration in
fine increments or to move the printed image completely relative to the sensor
mark. Adjusting the Print Offset setting affects each of the four print stations at
the same time. To adjust the print stations individually, refer to the section on Print
Line Adjustments.
To set the Print Offset via the front panel:
Press the NEXT or PREVIOUS key until the Print Offset menu is displayed.
Press the + or - key until the desired print offset setting is displayed.
• Print offset settings are -1200 through +1200
• Negative values move the image down on the label (out away from the printer)
• Positive values move the image up the label (in toward the printer).
Print offset settings are measured in single pixel (or dot) increments. On the QLS-
4100 X, there are 12 pixels per millimeter.
Press the SELECT key to confirm your choice.
Note
Setting the print offset via software will always override this setting. You
can set the print offset via Color QuickLabel 99 Pro or the QuickLabel
Systems Windows Printer driver.
Print Offset
1
2
3
4
Pause: Print Offset
Offset = 0 *
- Operation & Setup Guide 1
- Table of Contents 3
- 1 Quick Start 7
- QuickLabel Systems Media 8
- Quick Start Guide 9
- 2 Physical Setup 10
- Unpacking the Printer 11
- Printer Orientation 12
- Features of the QLS-4100 X 13
- Side View 14
- Rear Panel View 15
- Installing the Unwind Mandrel 16
- Power Connection 17
- Computer Connections 18
- Centronics Parallel Port 19
- RS-232 Serial Port 20
- Network Connection 21
- Utility Port Connection 22
- Compressed Air Connection 23
- DIP Switch Settings 24
- 3 Loading Media and 26
- Calibration 26
- Loading Label or Tag Media 29
- Adjusting the Media Sensor 32
- Calibrating Media 33
- Pause: Gap 35
- Calibration Bad 35
- 4 Keypad Controls 39
- and Menus 39
- Keypad Layout and Functions 40
- Deletes all labels 41
- SELECT to confirm 41
- Menu Functions 42
- Print Speed 43
- Pause: Speed 43
- Speed = 4 in/s * 43
- Print Intensity 44
- Pause: Intensity 45
- Head 1 = 12 * 45
- Print Offset 46
- Pause: Print Offset 46
- Offset = 0 * 46
- Windows Print Mode 48
- Ready: Windows Print 48
- Repeat 10 Label(s) 48
- Mirror Mode 49
- Pause: Mirror Mode 49
- Cutter Flag 50
- Pause: Cutter 50
- Flag Off * 50
- Cutter Offset 51
- Offset = 0 * 51
- Print Line Adjustment 52
- Pause: Test Print 52
- Proc. Block Pattern (CMYK) * 52
- Pause: Print Line Adj 53
- Head 1 = -4 * 53
- Cross Web Adjustment 54
- Pause: Cross Web Adj 55
- Head 1 = < 5 * 55
- TTR Sensor 56
- Pause: TTR Sensor 56
- Enabled * 56
- Calibrate 57
- Test Print 58
- Test Pattern: 1 in * 58
- Factory Reset 59
- Pause: Factory Reset 59
- Press SELECT 59
- Resets all settings 59
- QLS Settings 61
- Pause: QLS Settings 61
- SELECT to print 61
- System Baseline 62
- Pause: Sys Baseline 62
- Baseline = +3 * 62
- TTR / Media 63
- Pause: TTR/Media 63
- Standard * 63
- TTR Drop 64
- Pause: TTR Drop 64
- Head 1 = 22 * 64
- 5 Operation 65
- Printing with the QLS-4100 X 66
- RUN with NO AIR ? 67
- Press: Select 67
- Printer Indicators 68
- Error Messages 69
- Format Error 70
- Head x up 70
- SELECT to disable 70
- Head x Disabled 70
- Drive Roll Up 70
- Printheads Disabled 71
- Hd1 Hd2 Hd3 Hd4 71
- Color Alignment 72
- Evaluating print quality 77
- Advancing the Media 78
- Adjusting the Print Speed 79
- Printing Labels 81
- Printing Test Patterns 82
- 6 Advanced 83
- Adjustments 83
- Printhead Tangency Alignment 84
- Tools Needed 85
- Printhead Lift 87
- Adjusting System Baseline 88
- 7 Maintenance 89
- and Repair 89
- Recommended Tool List 90
- Routine Cleaning 91
- Printhead Replacement 92
- Platen Replacement 94
- Drive Roll Replacement 95
- Pinch Roller Replacement 96
- Firmware Upgrades 98
- Appendix A 99
- Physical Data 99
- QLS-4100 X Dimensions 100
- Appendix B 102
- Specifications 102
- QLS-4100 X Specifications 103
- Appendix C 104
- Replacement Parts 104
- Color QuickLabel 99 Pro 106
- Appendix D 106
- Color QuickLabel 99 Pro Setup 107
- Appendix E 111
- Windows Printer Driver 111
- Windows Printer Driver Setup 112
© 2020, manymanuals.com. All rights reserved. | 0.330 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals